How to disassemble round door handles. Door handle repair
Often you have to deal with situations such as repairing a door handle, replacing it, reinstalling it on another canvas. The very process of extracting this element is simple, especially if the design is not equipped with a locking mechanism. How to disassemble the door handle correctly? To do this, you must follow certain rules.
Fittings, distinguished by their beauty and good quality, serve as a wonderful decorating element of any door. Familiar to all handles allow you to freely enter and exit through the door, use it. Modern industry produces a huge variety of such products, differing in color, shape, quality, price, material of manufacture.
To ensure that the door is securely fixed in one position and does not open at the slightest movement, it is equipped with a special handle with a latch. This device should provide a soft and smooth movement of the structure. Particularly noteworthy are products of rounded shapes, the lock of which is equipped with a drum closing mechanism. This requires dismantling the device. In order to clearly and systematically carry out such work, you should prepare the necessary devices:
- Phillips or flat screwdriver;
- key with emphasis;
- wrench and pliers.
How to disassemble a round door handle? This problem is of interest to most of the craftsmen who repair, reinstall the door. Usually these elements on the same plane have a special locking mechanism that operates from a key. Having prepared the necessary devices for work, you can begin dismantling. How to remove the door handle? To do this, use a flat screwdriver, which can be easily removed the decorative elements of the mechanism.
Then they are removed from the valves located at the points where the handles are located. Then, using a key or other pointed product, you need to press on the stopper that appears. However, the handle should be pulled and removed. The screws that appear are unscrewed with a Phillips or flat screwdriver. Next, two halves of the mechanism are removed from the canvas. All screws are removed. The product should be disassembled in the same sequence, observing the reverse order. You need to start by fixing the heck on the canvas.
It is placed with the beveled part of the tongue at the opening point of the structure, then the part is fixed with two screws. After that, the parts of the handle are installed, it has a turnkey drum device. A clamping element is placed on the reverse side, then it is fixed with screws. In the process of work, it is necessary to control the strength of fixing the screws, slightly turning the door element and returning it to its original position.
If desired, you can center this element. A decorative part is fixed to a given point. The clamping part, fixed on the canvas earlier, is intended for mounting a moving element on it. Attention should be paid to the correct location of the square tube and the plate present at its base. How to disassemble the handle? For the accuracy of the work, it is necessary to turn the fixing part so that the opening coincides with the square-shaped hole in the same position as the tube of a similar configuration with a flattened plate.
Now you can install the product in its place. After it gets into the stopper, it is necessary to press in a transverse position relative to the clamping element, pressing it. The removed part of the product should be moved to this part to the end. Now you can install a decorative element. For such purposes, it is combined in the grooves and put on to the base.
Do not forget to check the handle for strength. After installation, you need to test the effect of this door element, and from both sides. It is necessary to monitor the correct operation of the latch and the drum device with a key. Any deficiencies should be eliminated.
How to disassemble the handle correctly? With such a simple work, you can completely cope on your own, you just need to clearly follow certain steps. Most often, products with latches and locks are installed on interior doors. In order to better understand how to remove the handle, we suggest that you familiarize yourself with the main stages of the process of dismantling this element.
- Study the structure of the handle. You need to carefully consider it, determine the method of connection with the door.
- Unscrew the fasteners and release the product.
- Unscrew the handle from the interior door, fixed on a separate base. Unfasten the spindle. In the same way, release the product from the opposite side of the door leaf.
If further painting of the door leaf is required, then it is necessary to remove the layer of old paint, clean the base with sandpaper. Then the door must be washed with water and detergents, after which the surface must dry. After sanding the canvas, you can start painting it. To perform the above work and install a new handle, you may need:
- different types of screwdrivers;
- bucket, napkin;
- putty, spatula;
- fine sandpaper;
- sanding pad;
- awl;
- drill;
- new door handle with lock, spindle and fasteners.
Installing a new handle is carried out in a certain sequence.
- Screw in the spindle.
- Using an awl, make marks for the screws securing the new product.
- Put the handle back in place.
- Make markup. Fix the spindle in the opening by putting a part of the product on it. The awl will help determine the location of the new fasteners that are inserted into the holes in the handle.
- Make indentations at the desired points. Tight door covering requires the use of an electric drill.
- Similar actions are carried out on the reverse side of the canvas.
- The handle is fixed on the spindle and mounted on the door leaf. Thus, the other part of it is attached on the reverse side.
Any new product must cover the screw holes completely. If they remain visible, they are sealed with wood putty. Using sandpaper, you can achieve a flawless polishing of the surface, then it can be painted. A product with a shorter base is replaced by a new one that comes with the kit. Any element of a pressure nature is represented by the right and left parts, they can have an identical appearance if the spindle is located in the middle of the mechanism.
Here it is important to trace the direction of rotation of the product before starting installation. Otherwise, you can install it the wrong way, and when you open the door, instead of moving down, it will move up. In order for the front part of the locking device to return to its former radiance, it is removed before the behavior of the installation. Unscrew 2 screws, lift the tongue. Old paint is removed with a special liquid, after which the tongue returns to its predetermined position.
In order to paint the canvas yourself, the handle is removed. Further, the place that was closed by it is well smeared. In this way, you can protect the fittings from getting enamel on its surface. Giving the door a new tone should be associated with applying two layers of paint to the surface. If desired, the canvas can be processed on both sides in different colors. To do this, a shade of the surface on which the loops are located is applied to the end parts.
Clearly and correctly assembled and installed fittings will ensure easy opening and closing of the door, regardless of the sides. If visible defects are found or the elements are loose, it is necessary to tighten and adjust them.
It will be useful for any owner to know how to disassemble the handle on the door, especially the interior one. This fitting is subjected to a serious test by all tenants, so someday it will fail, and it will need to be replaced with another one. In this case, you do not need to call specialists, you can handle it yourself, while saving on the employee's wages. Moreover, this business does not require great skill, but only a little skill. The dismantling process may differ depending on the type of handle, but the whole process should not cause any particular difficulties.
How to remove the handle from the interior door? Before proceeding with the analysis of the mechanism, you need to find out what kind of classification it belongs to. The division is based on several criteria. The one described below is suitable specifically for parsing a pen, because it has a classification according to design features.
Varieties of handles
Press. Such a handle is attached on both sides of the door leaf and has an L-shape. Opening occurs due to the load on the handle, after which the tongue is set in motion. The disadvantage of this fitting is that it is very traumatic.
Swivel. The opening method is the same as that of the push, only the tongue is set in motion not by pressing the handle, but by turning it. Such models are often not very convenient, because to scroll it, you need to have your hands dry, otherwise they will slip. When replacing them, a reasonable question arises about how to unscrew the interior door handle.
Stationary. This handle does not have a latch. It is attached with screws directly to the door leaf. It happens one- or two-sided, while it has an axial connecting element.
Reasons for parsing a pen
It is not so difficult to disassemble any of the models of door handles, because they have a similar design.
At the same time, disassembly of this fitting is extremely rare. What reasons can lead to this? How to remove the handle from the interior door?
The first reason is breakdown. It occurs most frequently. Often, inexpensive Chinese models are prone to breakdowns, which are not designed for a constant and rough load. If the prevention of some elements is not observed, then the fittings become unusable. It should be repaired, and sometimes the entire element should be replaced.
The next reason is the need for replacement. Every year the market is replenished with new and improved models. At the same time, you can choose a color scheme that suits the interior, or put a new, more functional and reliable model.
Renovation in a room often involves a change in style. Do not ignore the door handles. Therefore, the question often arises of how to disassemble the door handle.
Another reason is the spoiled appearance. If the part is made of low-quality material, then scuffs and scratches will be visible on it very soon, which negatively affects the entire interior.
Removing the push handle
How to remove the handle from an interior push-type door? This mechanism is more difficult to disassemble, because in its design there is an axis rod, due to which the handle is held. It is tightened with a tetrahedron.
The process of parsing the handle must begin with the removal of the plugs around it. They are fastened with screws or tightly pressed. They are very easy to remove with a minus screwdriver.
On one side of the door, you need to unscrew the fittings and remove. Then the second part is removed, on which the axis rod remains.
If the handle is with then it is also removed.
Following the sequence and accuracy will allow you to remove the mechanism without problems, without damaging the parts and without creating unnecessary hassle.
How to remove the handle from the interior door rotary with a rosette?
When there is no hole on the side of the swivel type fittings into which a key or screwdriver can be inserted, the elements are separated manually. Both parts of the handle should be scrolled in different directions and gradually removed from the thread. On one of them there will be an axial rod.
In this way, the socket is removed and the screws are unscrewed. When the axis is removed, you can do the following elements - a latch or lock, if necessary. When decorative parts are removed, you need to monitor the use of your strength, because overdoing it can damage the elements.
Removing the rotary knob
The handle with a lock for interior doors of a rotary type is removed as follows.
This will require a key to clamp the spring mechanism. Often it is not included in the package with the product, but it can easily be replaced by a nail or other thin object.
The first step is to remove the decorative plates, which can simply be pry off with a sharp object.
Use a key or nail to move the spring-loaded pin by inserting the tool into the technological hole located on the side. At the same time, pull the handle and remove it together with the cap.
After that, you need to move the fastening screws located on the plate. Then the two parts of the handle can be removed together with the axle.
Assembling the round door handles back is not difficult, only all the steps must be done in reverse order. First comes which is fixed with a plate, then an axis is inserted, fasteners are put on it. Decorative inserts are mounted last. The main thing is not to forget that the decorative flange is first threaded, and only then the main part of the handle is attached.
Removing the fixed handle
How to disassemble a fixed type door handle? They are the least likely to break or deform. This is due to the lack of moving elements in it. Often, door handles of this type are not repaired after removal, but are changed entirely. The withdrawal process is as follows:
- Self-tapping screws are unscrewed with a screwdriver.
- One part is unscrewed from the rod, and the second is removed along with it.
This design may not have a central rod, which greatly reduces the process. You only need to choose the right screwdriver to unscrew the screws of a certain diameter.
Removing the latch handle
First of all, when dismantling the latch handle for interior doors with an automatic lock, you need to remove the screws with a screwdriver. Next, unfasten the overlays. Use to unscrew the rod.
After that, pull out the rotary mechanism wrapped in a spring.
popular way
There are several ways to remove the latch handle for round-shaped interior doors with a latch. Here is the most popular one.
It is necessary to remove it with a screwdriver, first from the part where the latch device is located. It is necessary to press on the opened stopper and at the same time pull the handle towards you.
Then the latch is pulled out, for which the screws are unscrewed, after which the latch is released.
Thus, disassembling any door handle with your own hands is not a big problem.
Interior doors are sold without fittings, the delivery set includes only the door leaf and racks, from which the door frame is to be assembled. There are no factory-made holes in the canvas for installing locks and handles. This is due to the fact that handles, being standardized, have different designs and sizes. In addition, the choice of accessories depends entirely on the preferences of the buyer. Therefore, a person who has started repairs with the replacement of interior doors faces the problem of choosing whether to invite a master or install handles on his own. It should be noted that, having decided to install doors with your own hands, you will definitely cope with the installation of door handles.
Types of handles for interior doors
Door handles for interior doors can be classified according to the installation method, operation method, shape, material, and the presence of a lock.
According to the installation method, stationary (overhead) and mortise models are distinguished. Overhead are attached to the door leaf, and for mortise it is required to drill holes in it.
By way of work there are:
One of the most popular door handle materials is brass. In addition to excellent aesthetic properties, brass is practical and durable.
As a rule, complex locking systems are not installed on interior doors. An exception is the sanitary lock installed in bathrooms and toilets.
Installing a handle on an interior door
Consider the installation features of the most popular model for interior doors - knob handles. Handles are usually installed on a hinged door, however, many experts recommend removing the canvas for installation. True, this is not always easy to do.
Advice. If the canvas is not removed from the hinges and the installation is done in the hinged position of the door, move a chair or some object to it so that the door is stationary during your work.
Installation Tool
The tool will require the most common, which is in every home:
A marking scheme is attached to the door latch, but it is easy to make marks for the holes without it. From the bottom edge of the canvas on both sides, 1.0 meters are measured. 6 cm must be measured from each edge of the door and a mark is made. With the help of a square, a strictly horizontal line is drawn that will connect these two points. At the end of the canvas, a mark with a pencil and an awl is placed on this line in the center. A latch bar is applied and the veneer is cut with a sharp knife. Remember that the bar must be recessed into the door leaf so that it forms a single surface with the leaf.
Some experts advise starting drilling from the end of the canvas with a pen drill. With this sequence of work, the chips, when drilling with a crown, will fly out into an already made hole, and not clog the teeth of the crown.
The pen drill should go to the depth of the blade, no more. The drill is pressed to a point on the end of the canvas and a hole is drilled. Then, with the help of a crown, holes are drilled alternately on each side of the canvas; it is not necessary to make them through. As soon as the tip of the crown appeared on the opposite side, the drill must be stopped and drilling started on the other side. So the veneer will not be damaged when the crown exits.
After the holes are ready, with the help of a chisel and a hammer, we make a selection along the line cut with a knife under the latch bar. Install the latch and tighten with two self-tapping screws. It is better to take self-tapping screws not "regular", which are attached to the latch (they have ordinary soft metal), but high-quality ones.
Using the key that is included in the kit, we disassemble the handle into two parts so that it can be installed. To do this, one fixing screw must be loosened, the other unscrewed. The central rod is inserted into the hole and on one side the fixing screw is tightly tightened. Then the second half of the knob is put on the rod, and the second screw is tightened. Self-tapping screws are screwed on both sides, which will close the decorative overlays and the screws will not be visible.
After installing the knob-knob, it remains to install the "return" on the box. The door is covered, but not completely, and the upper and lower edges of the tongue are marked with a pencil. Using a square, the distance from the edge of the leaf to the center of the latch bar is determined, and this size is transferred to the door frame. Then a “return” bar is applied to the box, the veneer is cut with a knife, and a cutting is made under the bar and tongue with a chisel. The door is closed and the operation of the latch is checked.
Then a bar is installed on the box. Special “pockets” are sold for recesses under the tongue, they are made of plastic or metal. Self-tapping screws that fix the "return" bar can be closed with self-adhesive plugs. After that, the installation is complete.
How to disassemble and assemble the door handle of an interior door?
The installed handle-knob can be disassembled in two ways, depending on its design. Unfortunately, most of these models are of rather low quality and often fail.
Disassembly of one structure begins with the fact that you need to carefully pry and remove the decorative trim. The lining has a special groove, usually it looks down. The ball-shaped handle will interfere with unscrewing the screws, so you need to press the locking pin and at the same time, with a little effort, remove the handle from the central rod. Once the handle ball is removed, it will be very easy to remove the screws.
To disassemble the second structure, which does not have a locking pin, it is necessary to press the spring pin through the technological hole with the key from the delivery set and remove the handle ball. If the key length is not enough (it happens), use a simple nail. Then the decorative overlay and self-tapping screws are unscrewed. If you can't find the spring pin through the access hole, the knob has not been assembled correctly. Rotate the decorative trim 180° and the problem will be solved.
The handle is assembled in the reverse order.
The door lock has to be removed not only if it is replaced due to a breakdown. Like any other mechanism, the lock needs periodic cleaning and lubrication. The reasons for the removal of locks are different. You can call the master to remove the lock, but you have to wait. When there is no time to wait or there is no money for the master, you need to know how to disassemble the interior door lock yourself. It is not difficult to do this. To do this, you need to know how the most basic types of locks are disassembled. If the lock began to jam, it is necessary to find out the cause and eliminate it so that you can safely close and open the door. It is better to prevent a breakdown than to fix it later.
Stages of work: how to disassemble a round lock
Locks are installed on the entrance and interior doors. The most popular have recently become round handles with built-in locks. In their design there is a latch tongue, with the help of which the entire lock mechanism works. Swivel knobs may have a built-in lock that closes the door. To disassemble the round lock, you need a key. It comes with a lock included.
In order to find out why the handle broke, it is worth disassembling it and making sure what is the reason.
If the key is not at hand or it is broken, you can use any thin object to clamp the spring mechanism.
Steps to disassemble the nob handle and remove the lock:
- Clamp the spring mechanism;
- Move pin;
- Pull the handle;
- Remove the pen together with the cap;
- Remove the flange latch;
- Unscrew the fasteners on the plate;
- Completely remove the handle (its two parts).
It is necessary to move the pin with a key, inserting it into the hole that is located on the side of the handle. This must be done carefully. The lock is removed along with the handle, as it is built into it. This type of lock is mortise. It is also called round, since the handle itself has a spherical shape.
It will be more difficult to disassemble the front door lock. It can also have a round shape, but is built into the door separately from the handle. This one is more complicated than interior models. They are cut separately from the handles into the door leaf. Mortise locks may represent a cylinder model. They work with the help of a larva, which is a fixative. You can pull out the lock yourself. The cause of the breakdown may be in the larva. You can replace the larva itself or change the entire lock.
How to disassemble an interior door lock: the necessary tools
Many interior doors are equipped with handles that have built-in locks. Usually, such handles are installed on the doors to the bathroom or toilet. Often, owners save on fittings, so they install an inexpensive one. The locks in them can fail: the tongue sticks, the handle does not work, the key is stuck in the lock. These problems can be solved independently. The lock must be accompanied by instructions for disassembling it. If there is no such instruction, then you yourself need to understand how to disassemble it and fix the breakdown. It is necessary to find out the device of the lock in order to dismantle it.
The dismantling process may differ depending on the type of handle, but the whole process should not cause any particular difficulties.
For work you will need:
- Screwdriver;
- Pliers;
- adjustable wrench;
- A sharp object (awl, needle, hairpin).
Initially, you need to remove the overlay from the blocking button. After that, you can remove the mechanism itself.
The above tools are almost everyone in the house. You need to act carefully so as not to damage the decorative lining, the lock itself or the handle. Work should be done calmly and in stages.
Five ways to open the door: interior locks with handles
If the key is lost or broken, you have to open the lock yourself with improvised means. In any house there are objects with which you can open the door lock in order to repair or change it. Dismantling the lock is optional. Sometimes you just need to urgently open it to get into or out of a room.
It is important not to rush, knock out the canvas or break the lock - this is an extreme measure. You can return the mechanism to the "open" position using improvised means
You can open the lock with the following items:
- sheet of paper;
- plastic cards;
- Knitting needles;
- Screwdrivers;
- Shila;
- Knife;
- Files.
You can open the lock quickly: you need to insert a card or a sheet of paper between the canvas and the jamb. Push tongue. The mechanism will move and you can turn the handle.
After inaccurate emergency opening of the lock, it may be necessary to replace it. It will have to be removed from the door leaf and put a new one.
Interior latch locks: causes of failure and analysis
The reason for the jamming or breakage of the lock can be: the accumulation of dust in it, the lack of lubrication, the ingress of a foreign object, opening the mechanism with a non-native key.
In order to open a lock of a simple configuration, you will need improvised tools that are in every home.
There is a mortise lock with latch. Jamming can occur due to sticking of the tongue. The assembly of such a lock includes a spring mechanism. When broken, the tongue cannot move due to the spring.
To open such a lock, you must do the following:
- Move the tongue and tilt it to the side;
- Click on the handle;
- Drive the tongue inside the castle;
- Pull the door towards you.
If the door slams shut with the latch turned, you need to insert a thin tool under the handle, turn and remove it. After this action, the latch should fall into place.
How to remove the lock from the interior door (video)
When parsing any model of the castle, it is worth considering its structure. It is necessary to follow the sequence of actions when disassembling the lock. It is easy to disassemble the mechanism, but it is still worth reassembling it correctly. Carrying out the analysis slowly and carefully, after removing it, you can repair it and put it again. Sometimes the cost of a spare part for a lock is more expensive than the lock itself. In this case, it is easier to replace it completely and use it without any obstacles.
In this material, we will consider with you how to disassemble the knob knob, which have received an unusual distribution on interior doors. And also along the way we learn how these handles are installed. Below you can find not only instructions in pictures, but also watch a video.
To install the handle-knob, it is necessary to mark on the door and make two main holes, according to the template, which, as a rule, is included with the handle with installation instructions. So, let's start installing the handle, disassembling it along the way.
Given interior door:
We make a sample hole from the end of the door leaf under the latch. Hole diameter from 23 to 25 mm: It is convenient to make a hole with a so-called spade drill for wood.
With a crown on a tree with a diameter of 50 mm, a through hole is made for the main fastening of the handle. The distance from the end of the leaf to the center of the hole is 60 or 70 mm, depending on the latch that is included in the kit.
You can find a template for installing a knob-knob from some manufacturers in the form of a stencil on the inside of the box or in the attached instructions. It is very convenient to use ready-made kits for installation, which are called “kits for installing interior handles”. It is not scary (and often useful on the contrary) if the holes are made with a diameter of 1-2 mm larger than recommended. The latch mechanism is two-position: provides for the possibility of installing a knob on the door, with different widths of the first bar of the door. The removal of the center of the handle-knob from the edge of the door leaf in the standard is 60mm:
but by moving the sleeve under the square, you can set the distance to 70 mm:
The standard height of the handle on the door is approximately 950 mm from the floor level. Next, to install the knob-knob, we partially disassemble the inner half of the handle in order to gain access to the holes for the mounting tie-down screws. To do this, we will use a special “key” from the handle kit or any suitable item, for example, a knitting needle. There is a special hole on the handle, through which the door knob should be disassembled. In the presented photo, it is round, but it can be of various shapes. This hole is located at the bottom of the handle:
Through the hole we press the spring-loaded latch, while simultaneously pulling out the handle of the interior knob.
We take out the handle and completely remove it:
Then you need to pry off the outer decorative flange of the handle with any sharp object. Take a closer look, as a rule, the flange has a corresponding groove for this:
well, the knob-knob is disassembled and we got access to the mounting screws
Further assembly of the handle-knob occurs on the door in the reverse order.
First, install the latch in the door and secure with two screws from the end. It will look like this:
The rectangular front plate of the latch mechanism is mounted flush with the door leaf. To do this, marking under it, with a chisel, the required depth is selected at the end of the door leaf. The same applies to the striker of the knob, which is installed according to the markup, on the door frame. Also, under it, the required depth is sampled with a chisel.
Further, it is already possible to assemble the knob-knob on the door leaf, pulling together the disassembled halves with fixing screws. The square of the handle and bushings for the mounting screws will, during installation, pass through the previously installed latch, through its technological holes
Handles-knobs are universal and are not divided into left / right-handed. The design provides for the installation and adjustment of the knob for any door with a thickness of at least 35mm.
If the shape of the knob-knob has an asymmetrical shape of a ball, etc., then after installing the knob on the door, using the method described above, remove the knob handle, and change the outer and inner handles in places, having achieved their correct location, relative to the location of the door leaf ( left or right side). The latch or lock mechanism, if any, is also brought into the correct location, and if required, we also swap the outer and outer sides.
The handle, assembled and without distortions, installed on the door, should work easily in both directions and independently, under the action of a return spring, return to its original position. If this does not happen, then you need to check the evenness of the installation, as well as tighten or loosen the fixing screws, achieving their equal tightening and soft stroke of the knob.
